LX Navigation LX PowerFlarm Eagle Mobile

LX Navigation Flarm Eagle Mobile is a compact FLARM compatible “black box” unit. The unit is standalone, which means it has up to 15h of battery, LED display and built–in speaker. It is perfect to use in multiple aircraft.

LX Navigation LX FLARM EAGLE is a special order item. Please allow approximately four weeks for delivery.

• Internal micro SD card for FLARM configuration, firmware update or storing IGC flights
• IGC flight recorder applied for “Up To Diamonds”
• Preloaded obstacles (where databases are available)
• Internal Bluetooth
• Internal battery for up to 13h of operation
• Portable
• Onboard FLARM LED indicator
• Built–in 50 channel GPS and GPS antenna

• LX Flarm Eagle mobile
• Dipole RF Antenna
• Diversity Dipole RF Antenna (optional)
• GPS Antenna
• Quick guide
• Baro–calibration chart (optional)

• SMA FLARM RF connectors
• Micro USB port
• USB port

• PowerFLARM OEM Module

• IGC (International Gliding Commission) approved logger (optional)
• ENL (environmental noise level) for combustion engines (optional)

• LX FLARM EAGLE mobile
• LX FLARM EAGLE mobile ADS–B in
• LX FLARM EAGLE mobile IGC
• LX FLARM EAGLE mobile IGC ENL
• LX FLARM EAGLE mobile Pro*
• LX FLARM EAGLE mobile Pro* IGC
• LX FLARM EAGLE mobile Pro* IGC ENL
• (*Additional dipole antenna and diversity module.)

Your LX FLARM EAGLE comes with technical support and two–year limited warranty.

LX Navigation Flarm Eagle Mobile price varies depending on selection.
Use above dropdown box for selection and final price.

To Power ON the device press the PWR/MODE button. Once the unit gets GPS signal it will be operable. To Power OFF the device press and hold the PWR/MODE button until the lights go off.

Using of PWR/MODE button it is possible to adjust some parameters of the display (baudrate and hierarchy). Power OFF the unit, press PWR/MODE button and hold to power ON and continue holding for 4 seconds. The display parameter indication will change (see table below) after each press on mode selector for approximately 2 seconds. To change the selected parameter, press PWR/MODE short – the status will indicate circular LED’s.

Note: Default baudrate of LX Flarm Eagle mobile is set to 19200 bps. Please check and set to correct baudrate in case of communication problems

Find the ideal spot in your cockpit to install the device. Connect the FLARM RF antenna according to FTD–041 (www.flarm.com) and configure the unit prior to first use.

The LX FLARM Eagle mobile can be configured by the use of the config file stored on USB flash drive created with program 1 FLARM Tools. Always use the latest version of 1 FLARM Tools program on your PC.

Default settings:
• Flight recorder logtime is set to 4 seconds.
• Communication baud rate is set to 19200 bps.
• Output data is set to “navigation & FLARM”.
• Horizontal detection range is set to 25500 meters.

To create the config file, open the latest version of (1) FLARM Tools program (www.flarm.com). On the top navigation bar go to option Tools/Create Config File (left picture). You are presented with Flight Recording and Advanced subpages (right picture). Under Flight Recording, you will find options for Recording Interval and Pilot/Airplane properties, under Advanced you can find Connection settings, Radio settings, device ID for radio communication and ICAO 24-bit address in case you have transponder.

When appropriate settings have been made, click Save to generate the config file. Save the file to the root of USB flash drive, insert it into LX FLARM Eagle mobile and turn it on. The configuration will start automatically. Wait 5 minutes and restart it. Device is configured.

The most convenient way to download flights is via USB flash drive, as it is an automatic procedure. FLARM will store all finished flights from internal memory to USB flash drive (if it is inserted). Stored flights can be viewed on PC (.igc format).

To update device, download the latest FW version at www.lxnavigation.com/support/software and copy it to the root of USB flash drive. Insert the USB into the device and power it on. Wait 5 minutes and restart it. The LX FLARM Eagle mobile is updated.

Connect any FLARM compatible display to your LX FLARM Eagle mobile with Micro USB to RJ 12 cable to transfer the necessary power and data.

We recommend using LX FLARM Eagle mobile with LX navigation FLARM accessories – LX Traffic monitor, LX FLARM Color display and LX FLARM LED display. Discover more at www.lxnavigation.com.

Some settings in FLARM Firmware will not work correctly or will be limited if you do not use the latest FLARM Firmware version. Ensure that LX FLARM Eagle mobile is updated at least once per year

LX Navigation is one of the oldest glider navigation brands. Its founders started experimenting with glider computers way back in the 70's and the Company has been working on improving your flight performance ever since.

Throughout the last 40 years or so it has been working on instruments that most pilots will have used at some time. In fact their equipment can be found in almost any gliding club!

LX Navigation equipment has always been ground–breaking.

LX Navigation motto?

Be the first. Be the best. Be different.