AVIONICS AND ELECTRICAL INSTALLATION HARDWARE

AVIONICS INSTALLATION SUPPLIES
ALWAYS use approved hardware and wire when installing avionics
THERE REALLY IS A DIFFERENCE

FAA approved "Tefzel" Mil-Spec teflon insulated silver coated stranded copper wire has the ability to
self-extinguish flame, it is abrasion & corrosion resistant and designed to hold up under vibration.
22 Gauge TEFZEL.........................................$0.20 Ft
20 GaugeTEFZEL...........................................$0.20 Ft
18 Gauge TEFZEL..........................................$0.24 Ft
14 Gauge TEFZEL..........................................$0.24 Ft
Colored TEFZEL 22 Gauge size only...$0.28 Ft

Also available in shielded multi-conductor cable sets
best for avionics and variometer/GPS flight computer with isolated (shielded)
wire sets to reduce RF interference
22 Ga 2 conductor M27500-22TG2T14 $.75 per foot
22Ga. 3 conductor M27500-22TG3T14 $.90 per foot
20 Ga. 2 conductor M27500-20TG2T14 $.80 per foot
20 Ga. 3 Conductor M27500-20TG3T14 $.95 per foot
16 Ga. 2 conductor M27500-16TG2T14 $1.05 per foot
COAX CABLE
RG58C/U

BELDEN RG-58C/U MIL-C-17G (8262) Coaxial Cable Stranded tin-coated copper conductor. Diameter .116"
recommended for normal communication transceiver installations.
$0.66Ft.

COAX/RG400

 MIL-C-17/128 (RG-400) Coaxial Cable Solid silver-plated copper conductor. Diameter .116"
Highest grade Coax cable, recommended for Transponder installations
$3.76 ft.

Landing gear warning kit
a simple do-it-yourself kit including all of the needed parts and diagram to build a simple
9V Battery operated warning system to activate when spoilers or landing brakes are opened and landing gear is
still in the up position.

Included along with a simple diagram
(2) lever switches
(1) Loud "panel mount" buzzer alarm
(1) Miniature Push-To-Test switch
(1) 9 Volt battery holder
(1) 20 foot 22 Gauge wire
Complete kit $46.95
 

DIN CONNECTORS

Becker type type DIN connector 5 pins at 180 degree $14.00
Walter Dittel type DIN connector, 5 pins at 270 degree $14.00
Also available
Din connectors for Battery boxes and other accessories
2 PIN with centering lug at 180 degree (WD Battery box) Sorry, NLA
3 Pin 180 degree (Filser battery box) $14.00
Please note; the 2 pin DIN connectors previously used on WD Battery box are no longer available and have been replaced with new 3 pin connectors as seen in this image below and fit the new battery boxes only, not interchangable.

old type (left) had large plastic centering blade
mew type on right has 3 pins
DIN Sockets
Ideal for panel mounting, quick-disconnect electrical connections with locking ring
Use for panel mounted battery charging, removable panel set-ups or with microphones

2 PIN with centering lug at 180 degree  (Walter Dittel battery box type) $10.85
5 pins at 270 degree female panel mount socket $10.95

Solder or Crimp type male and female  BNC Coax connectors

SMA to BNC Adapter
as used on many Vertex Standard handheld radios to connect to external crew and base station antennas
$11.00


(left) BNC Male Crimp type and  (right) Female (Jack) crimp type connectors for RG58 cable
BNC-174 Crimp type connectors for RG174 GPS antenna cable
$7.95 each
(*requires special crimping tool)



(left) BNC Female  and (right) Male solder type connectors for RG58
$7.95

BNC Female Bulkhead mount *Crimp only) connector for RG58 (*requires special crimping tool)
$8.75
note: Crimp type connectors require special crimp tool for installation

SMA-RG58 Bulkhead connectors

Crimp type for bulkhead mounting
*requires special crimping tool $8.95


Easy to install, no solder connector, (PL259 type) RF coaxial, for RG58 cable used for antenna connections
$6.95

PL259 Type Connector, Not common with base antenna connections
$7.95

Microphone and Headphone Jacks and plugs

PJ068 3/16" 3 contact microphone plug $16.95

1/4" 2 contact headphone plug $9.95


JJ033  3 conductor Aviation Mic Jack....$7.50
JJ034 2 conductor Aviation Headphone Jack $6.50

The AG mic & phone jack housing

are made from aluminum, painted with a crinkle finish (AG-JH1)
Jacks not included.
$19.95

Panel mounted Fuse Holders

Panel Mount holds 3AG type fuse
available as front mounted (normally must be soldered in place at the panel)
$4.95
or rear mounted type


(can be part of a pre-assembled cable set and installed from the rear of the panel)
$7.95

Polarized connectors
Cinch 2 pole electrical connectors are ideal for protecting polarity
one large and one small flat blades insure they can only be connected one way and cannot be reversed. Use for battery connections or other removable electrical connections.

Cinch 2 socket FEMALE polarized connector $7.95
CINCH 2 pin MALE connector $7.69

Toggle Switches

Miniature Toggle switches are used for a variety of applications
 Part 683-0267 is a miniature ON/OFF toggle switch $5.95
 Part 683-0268 is a miniature toggle switch, ON-OFF-ON positions like used for switching from one component to
another or from one power source to another $7.95


Terminal Barrier Strips
 8 position terminal strips (Pictured above) with 4 terminal  jumpers included $5.95
12 Position Terminal Strip with 4 terminal jumpers included $5.95
16 Position Terminal Strip with 5 terminal jumpers included $8.55


Made of white nylon, for wire size, 22-12 AWG maximum Amps Per Circuit 20 @ 300 VAC/VDC.
To make a connection, insert stripped wire into a terminal opening and tighten the screw.
The blocks have a mounting hole between every circuit (screws not included)
4 position terminal strip $4.50
8 position terminal strip $6.00
10 position terminal strip $7.50

Push-To-Talk Switch/Harness

Expensive, but very high quality, made to last, all metal  momentary, normally open, with "click" (feel- hear)
feature and three meter shielded cable...$64.00



Miniature, momentary, normally open  PTT (push to test, push to talk) switch,
black button is lower cost and good quality
MSPS103C0 $6.95

Toggle Switches

Miniature Toggle switches are used for a variety of applications
 Part 683-0267 is a miniature ON/OFF toggle switch $5.95
 Part 683-0268 is a miniature toggle switch, ON-ON positions like used for switching from one component to another
or from one power source to another $7.95

HARDWARE

6-32 1/2 PANHEAD SCREW (B.B.)
6-32 1" PANHEAD SCREW (B.B.)
Instrument mount screws, 1/2"x 6-32 brass black colored screws round  head..$.45 ea.
Instrument mount screws, 1"x 6-32 brass black colored screws round  head....$.60 ea.
 6-32 non-magnetic brass nuts
Metric Instrument Screws (Black Brass)....$.60 ea.

SPEAKERS
Pedestal Mounted 3", 8 ohm
3 inch Mylar cone speaker with mounting bracket 8 Watts. 8 Ohms, 6ft cord compact 3 3/14x3x2 1/4inches

$25.00
 
Pedestal Mounted 2", 8 ohm
Low cost pedestal case for deck mounting also can also be easily adapted to mount in 57mm (2 1/4") Instrument panel openings.

Pedestal 8 ohm small box speaker
Similar to the above speaker but in 8ohm $34.00

Microair SP01 Box Speaker

This small speaker is housed in an attractive black grill box. The SP01 is 8 ohm,
5 watt, and terminated with a 2m shielded wire lead.
$35.00



From Walter Dittel Open 4 Ohm speaker 3.5cm deep x 7.8cm square (Bolt circle 5.8cm)
or  8 ohm open speaker, 2.5cm deep x 5cm square suitable for most aircraft radios
$29.00

Open Speakers
NEW Surplus Speakers, limited supply

 AUDAX (France) 5" 4 ohm Open speaker
Excellent sound quality even at high volume for noisy environments
 $17.00

High quality speakers for radios insure clear communications
4" 3.2 ohm communications loudspeaker

simple low cost loudspeaker 4" square excellent for voice communications
$10.95

Mylar (polypropylene) cone speaker
similar to the above loudspeaker but waterproof Mylar cone rather than standard paper type cone

3.2 ohm, 3 watt waterproof clear polypropylene cone speaker
3-7/16" square x 1-1/4" deep. Mounting holes 2-13/16" across, 3-15/16" diagonal
$22.50

RCA 4" 4 ohm Mylar Cone loudspeaker

$20.00